1S Bms / Pcb 1Mos - 5530 - 3A - 3.6V

Customer Reviews

To moderator Review by YVES SOUSSI

Rating

please replace "1 pcs of 1x 18650 Battery holder with wires"

with "1 pcs of 1x 18650 Battery holder with wires that you can purchase from Nkon at the lowest price on the market, if it is not "OUT OF STOCK""

Thank you !! - YVES



(Posted on 01-05-18)

From Li-Ion to Li-Ion battery: design a new battery pack for old mobile phone Review by Yves Soussi

Rating

Hi

1) From Li-Ion to Li-Ion battery: design a new battery pack for old mobile phone

For my hobby I purchase for a few euros obsolete mp3, telephone, PALM organizer, camera, with dead Li-Ion battery

And I replace the dead Li-Ion battery with a new 12W Li-Ion Battery , it is very easy ! And it is funny. Most of the time obsolete electronics product are more rugged, better quality than new one and they cost almost nothing: all they need is a new Li-ion battery that you can purchase at Nkon.

2) Recycle old mobile telephone and start your new business !!

3) How to do it : for a telephone (for a MP3, it is much simpler)

What you need

1 pcs of 18650 unprotected Li-Ion, the highest capacity is the better (i.e. Sanyo NCR18650GA 3350mAh - 10A).from Nkon

1 pcs of 1x 18650 Battery holder with wires

1 pcs of 1S PCM/PCB 1MOS - 5530 from Nkon (the lowest price on the market, they sell it x5 price on Ebay !!) to protect the Li-Ion.

1 pcs of wrapping or a plastic case to protect the case of the Li-Ion

1 pcs of soldering Iron

1 pcs of small PCB

1 pcs of resistor 7.4 Khoms to replace the Thermistor

Here is a video = https://www.youtube.com/watch?v=Kt9Eqo_vfSU

Good luck, and now you start new a Job if you read me !!

Bien à vous
YVES SOUSSI


(Posted on 01-05-18)

PCB Diagram Review by Yves SOUSSI

Rating

1) PCB Diagram Bottom Layer

You need a Li-ion battery with soldering tabs.

On Bottom Layer of the PCB, you will "B+", the pin where you connect the wire "+ " of the 3.7V Li-ion Battery;

2) On the other side , top layer, you wil find "B - ", opposite side of "B+" the pin where you connect the wire " - " of the 3.7V Li-ion Battery ;


You wind also "Protect +" and "Protect - " pins P+ and P- , these pins are the 3.7 V protected output.

No NTC on this PCM (Protection Circuit Module)..for temperature protection.

best regards
YVES SOUSSI







(Posted on 02-04-18)

Data sheet 1S PCM/PCB 1MOS - 5530 Review by YVES SOUSSI

Rating

Hi

1) Data sheet 1S PCM/PCB 1MOS - 5530

design a new battery pack for old mobile phone

Data sheet is here http://www.pc-caps.com/yves-soussi.nsf/docs/AXDE5TYSOU?opendocument&subcat=fromli-iontoli-pobattery:designanewbatterypackforoldmobilephone (Posted on 31-03-18)

3.7V 2.5A 1S Lithium Battery Protection Board Module Polymer BMS PCM PCB Review by YVES SOUSSI

Rating

Hi

1) 3.7V 2.5A 1S Lithium Battery Protection Board Module Polymer BMS PCM PCB

Product Introduction;

1.Charing Voltage:DC 4.2--5V CC/CV

2.Single Battery Consumption Current:<=6uA continuous discharging current 2.7A

3.Overcharging Detection Voltage:4.2 V+/-0.025V

4.Overcharging Detection Delay Time:150-500 ms

5.Overcharging Restore Voltage:4.0V+/-0.025V

6.Overdischarging Detection Voltage:2.75V+/-0.1V

7.Overdischarging Detection Delay Time:50-150ms

8.Overdischarging Restore Voltage:2.9V+/-0.10V

9.Overcurrent Detection Voltage:150+/-30mv

10.Overcurrent Detection Current:4.5+/-0.5A

11.Overcurrent Detection Delay Time:5ms-15ms

12.Overcurrent Restore Type:automatic restore

13.Short Circuit Detection State:external short circuit

14.Short Circuit Detection Delay Time:<=50us

15.Short Circuit Restore State:automatic restore

16.Internal Resistance:MOSPET <= 40m ohm

17.Operating Temperature Range:﹣40~+50degree

18.Storage Temperature Range:﹣40~+90degree

19.Size:28*3.8*1.2mm



Features:

1.Connecting Charger Teminal adopts withstand high voltage instrument

2.Internal 3 phase overcurrent detectiton circuit (overcurrent 1,overcurrent 2,load short circuit)

3.MOS tube can control battery charging and discharging

4.Wide Operating Temperature Range

5.Low Consumption Current



Soldering Point Introduction:

1.B+:connect with power positive

2.B-:connect with power negative

3.P+:connect with charging/discharging port positive(charging port/discharging port common used)

4.P-:connect with charging/discharging port negative(charging port/discharging port common used) (Posted on 31-03-18)

How to make your own protected battery for phone, MP3, ipod, palm, sony VGF AP1, any device with li-ion Review by YVES SOUSSI

Rating

Hi

1) How to make your own protected battery

(I will publish picture and a small video soon)

Purchase 18650 cell, this IC, and a 1 cell holder for phone, MP3, ipod, palm and you are done.

Overcharging Restore Voltage: 4.0V+/-0.025V MPN:

Overcurrent Detection Voltage: 150+/-30mv

Country/Region of Manufacture: China

Overcurrent Detection Current: 4.5+/-0.5A

Input Voltage: DC 4.2--5V CC/CV

Operating Temperature Range: ﹣40~+50℃

Size: 28*3.8*1.2mm

Internal Resistance: MOSPET <= 40m ohm

Overcharging Detection Voltage: 4.2 V+/-0.025V
(Posted on 31-03-18)